Archive for the ‘LX9 MicroBoard’ Category

Peripheral Modules from Digilent and Maxim

July 12, 2012

For those who own or will own Avnet LX9 MicroBoard, Digilent boards, ZedBoard, and Xilinx ZC702, or any other FPGA boards with Pmod ports, Pmod with analog and mixed-signal functions is a must have to pursue interesting and fun projects.

Pmod™ is the trademark of Digilent. Pmods are 6 or 12 pin small I/O boards to extend FPGA boards.
Digilent sells many peripheral modules, almost 50 ones in total, price ranging from $9.99, such as slide switches, LEDs, and RCA audio jacks, to $59.99, a 802.11b WiFi. They includes input/output, sensors/actuators, DAC/ADC, and connectors, etc.

Maxim announced a collection of 15 Pmods, called Maxim Analog Essentials Collection, early this month.
The $89.95 collections has the following Pmods:
Octal 12-Bit DAC
16-Bit ADC
16-Bit High-Performance DAC
RS-485 Half-Duplex Transceiver
8-Channel Relay Driver
All-Silicon Clock Oscillator
600V Isolator for SPI/UART
Proximity and Ambient Light Sensor
±5ppm I2C Real-Time Clock
Digital Thermometer/Thermostat
Type K Thermocouple-to-Digital Converter
Dual Nonvolatile Digital Pot
Programmable Current Limiter and ADC
16-Port GPIO and LED Driver
±15kV True RS-232 Transceiver

MAXPMBAE – Maxim Analog Essentials Collection of Peripheral Modules

Here‘re some more details, and Product Brochure.

EDN has a product review Maxim’s collection of peripheral modules for FPGAs, it covers Maxim’s offering, and some useful information about Pmod.

I will order one for sure, it is well worth it, considering single Pmod could cost around $20.
I hope and believe more reasonably priced peripheral modules, with diverse functionalities, will show up.
FMC is more powerful but expensive, it may be out of reach for many.

If you have any ideas for a fun FPGA project and don’t mind to share, please do.

 

Advertisements

Install Xilinx Cable Drivers on 32 bit Ubuntu

May 11, 2012

Xilinx released ISE 14.1 this week. Unfortunately Ubuntu is still not a supported OS platform. I have to go through the driver installation process again, but this time I documented what I did and hope it will be useful for Linux users of Xilinx design tools.

My 32 bit Ubuntu 10.04 VM is of version 2.6.32-38; ISE 14.1 is installed on a remote hfsplus mount. Since it is a virtual machine, I enabled X11 Forwarding via SSH on OS X host to allow GUI installation.

Install ISE 14.1

Install ISE 14.1 suite, including ISE, LabTools and SDK, without cable drivers. Run xsetup scripts as regular user. It took about 22 GB disk space on the remote mount.

Setup Environment, and Install Supporting Packages

The default Ubuntu shell is dash, a smaller but less feature-rich shell. I changed the shell to bash.
Point gmake to /usr/bin/make.
Some packages are required to compile driver:

  • libusb-dev
  • libftdi-dev
  • build-essential
  • libc6-dev
  • fxload

Here’s my setup environment.

Environment and Packages

Build and Install Drivers

I followed the advice from George Smart:
Xilinx JTAG Linux
Here’s how I compiled and installed driver.

Compile and Install Driver

Connect FPGA Device via Platform Cable USB II

I’m using LX9 MicroBoard. There are 3 different ways connecting to JTAG.

JTAG     USB Device ID Cable Speed (MHz) or Clock Frequency(100,000Hz)
Platform Cable USB II 03fd:0008 6MHz
Digilent Onboard Plugin 1443:0007 4m Hz
Digilent HS1 0403:6010 10m Hz

Here’s how I connected to FPGA.

Platform Cable USB II

Install Digilent Onboard Plugin Driver and Adept Driver for HS1

Here’s how to install Digilent drivers, and connect via Onboard Plugin port.

Install Digilent Drivers and Connect via Onboard JTAG

Connect FPGA Device via Digilent HS1

Connect to JTAG via HS1 is identical to Platform Cable.

Connect FPGA Device via Digilent HS1

Here’s how to use impact to connect, please notice JTAG clock frequency is listed.

Impact Connect via HS1

To Do

I have a 64 bit Fedora 14 Desktop. Get the drivers built and installed is much more challenging. I will report back if I could get it work.

Configure FPGA/SPI Flash to Run Linux on LX9 MicroBoard, Part 1 – Preparation

October 17, 2011

This is Part 1 for the topic, to prepare configuration data for LX9 MicroBoard.

The FPGA design is done with ISE 13.2 based on AXI/Little Endian MicroBlaze 8.20a. The details were presented here at Run Linux on Avnet Spartan-6 LX9 MicroBoard.

The Linux kernel is built with Petalinux SDK 2.1. You may contact PetaLogix to obtain a license and SDK to try out. If you prefer Xilinx’s embedded Linux solution, you can find useful information from its Open Source Wiki. From configuration point of view, it makes no difference which one is used.

The keys to prepare the configuration data are:

  • understand how SPI Flash is partitioned
  • understand how each partition is used
  • make sure proper sizes for partitions, especially for the partition where Linux is at

You may need build kernel more than once, if you don’t know the kernel size beforehand. For example in the second build, you can adjust partitions to fit Linux into flash.

Here’s Flash partitions used by Petalinux, and sizes are modified because of 11MB kernel. Note SPI Flash on the MicroBoard has 256 64KB blocks, total space is 16MB.

Partition Name Size (blocks) Flash Address Usage
0 fpga 2MB (32) 0x0 bitstream and fs-boot
1 boot 256KB (4) 0x200000 u-boot
2 bootenv 128KB (2) 0x240000 u-boot environment variables (not used here)
3 config 128KB (2) 0x260000 used by flatfsd to store persistent data, required but not used by configuration
4 image 12.5MB (200) 0x280000 Linux kernel and filesystem
5 spare 1MB (16) 0xf00000 remaining space (not used here)

Here’s how partitions are specified in kernel configuration (System Settings -> Flash Partition Table -> Image Partition Size).

System Settings

Flash Partition Table

Image Partition Size

Once the kernel is rebuilt, along with the outputs of FPGA bitstream from ISE/EDK, and U-Boot from XSDK, the following files are used to construct configuration data, and/or bootstrap Linux:

File Description Built by Usage
system_bd.bmm BRAM memory map ISE/XPS to generate download.bit by script d2m
mb_system_top.bit design bitstream
fs-boot_0.elf fs-boot XSDK
u-boot.elf u-boot executable Petalinux SDK not used by configuration, but useful to transfer images to Flash
u-boot-s.bin u-boot relocatable binary to generate sopc_lx9.mcs by script pgen.ub
image.ub Linux kernel and filesystem binary

This is the script d2m, a wrapper of data2mem:

d2m
#!/bin/sh
data2mem \
  -bm mb_system_bd.bmm \
  -p xc6slx9csg324-2 \
  -bt mb_system_top.bit \
  -bd fs-boot_0.elf \
  tag microblaze_0 \
  -o b download.bit

This is the script pgen.ub, an wrapper of promgen:

pgen.ub
#!/bin/sh
promgen -w \
  -p mcs \
  -c FF \
  -o sopc_lx9 \
  -s 16384 \
  -u 0000 download.bit \
  -data_file up 200000 u-boot-s.bin \
  -data_file up 280000 image.ub \
  -spi

The following capture summarizes the procedure to generate configuration data.

Generate Configuration Data

If you would rather prepare PROM from iMPACT GUI, here’re the steps (Note, the files could be at any folder).
Launch iMPACT and select “Prepare a PROM File”.

Prepare PROM File

Select and Enter as following (highlighted).

Prepare PROM Steps

Add device bitstream.

Add Device Bitstream

Add 2 data files.
The first one is U-Boot, and make sure it is at proper address on Flash, in this case it is 0x200000.

U-Boot Flash Address

Add U-Boot

The second data file is Linux kernel and filesystem. Make sure the Flash address is set to 0x280000.

Kernel Flash Address

Add Kernel

Here’s the resulting data file assignment.

Data File Assignment

Proceed to generate configuration data.

Generate File

You can find scripts and source data files from here.

As a side note, when people move to high end FPGA solutions with processor integration, as Xilinx calls Zynq as EPP (Extensible Processing Platform), and Altera calls SoC FPGA with HPS (Hard Processor System), there is less or no need, in a sense, to configure FPGA from persistent storage such as Flash. The processor can easily make bitstreams and software images available to FPGA.
For large volume and low cost applications, soft-cores such as MicroBlaze and Nios are good solutions, and configuration is still needed.

Configure FPGA/SPI Flash to Run Linux on LX9 MicroBoard, Part 3 – Easy Way

October 15, 2011

This is Part 3 for the topic.
In Part 2 – Quick Way, network connection and tftp server, plus certain knowledge of U-Boot are needed. You can avoid them by just using iMPACT to program the FPGA/SPI Flash. Here’s how.

On the host with Xilinx design tools installed, navigate to the folder with following files.

File Description Usage
sopc_lx9.mcs configuration data program FPGA/SPI Flash
impact.cmd programming script for Xilinx USB II cable (6MHz)
impact.12Mh.cmd programming script for Xilinx USB II cable (12MHz)
impact.onboard.cmd programming script for Digilent Onbard JTAG

Program FPGA/SPI Flash by running iMPACT in batch mode.

USB II Batch Program

The Linux kernel and u-boot has a size about 10MB (still have some rooms left for 16MB Flash, I could see many potentials there), and FPGA/fs-boot has only 336KB. The final MCS data triples the size (in ASCII format).
It takes about 68 minutes on my Linux host, including verification. Program alone may take about 43 minutes, by using default JTAG clock speed, 6MHz.

USB II Program Done

With impact.12Mh.cmd, it takes about 35 minutes. iMPACT complains 24MHz is not supported.

Program at 12MHz

I also tried several times to program by using MicroBoard’s Onboard USB/JTAG. It is supposed to be running fast (in 15MHz?). By 1) modifying Avnet Tom’s script listed in LX9 board forum Remarks on AvtS6LX9MicroBoard_SW302_PetaLinux, and 2) by iMPACT GUI, but I was never able to go to the end. I remembered once I let it run overnight from GUI, it was less than half way through in the next morning, and I had to abort the process.
It could be I didn’t specify options correctly. I attach the programming script for Onboard JTAG, just for reference, but be warned, don’t try it, it may take forever to program.

If you’re more interested at programming through iMPACT GUI to have a good understanding what’s going on, here’re some screenshots.

Start iMPACT by choosing “Configure devices using Boundary-Scan (JTAG)”.

Configure Devices

Select “No” for “Auto Assign Configuration Files Query Dialog”.

No for Auto Assign

Right click the device from “Boundary Scan” tab to add SPI Flash.

Add SPI Flash

Select attached SPI Flash (N25Q128 1.8/3.3V).

Select SPI Flash

Right click added SPI Flash device and select “Program”.

Program

It achieves identical result as running the script in batch mode, and takes about the same time to finish.

If you’re interested, here’s the link for scripts and configuration data.

Configure FPGA/SPI Flash to Run Linux on LX9 MicroBoard, Part 2 – Quick Way

October 13, 2011

This is Part 2 for the topic, I will present Part 1 (Preparation) after Part 3 (Easy Way) is done.

Petalinux is using a 2-stage booting process. The First Stage boot, FS-Boot, is running from FPGA’s BRAM once powered on. It’s sole responsibility is to load the main system bootloader, i.e., U-Boot, from the flash to the larger external memory, and run U-Boot from the external memory.

One of the quick ways to configure FPGA is to copy binary images to the flash, instead of programming it, which could take significant time depends on programmer used.

In order to do that, networking connectivity and a mechanism to deliver and retrieve images are required.
As used by almost everyone, I’m using tftp. The host runs tftpd is connected to the LX9 MicroBoard via a router.

The following images are needed.

Image Description Usage
download.bit bitstream plus fs-boot binary FPGA and fs-boot image on flash
u-boot.elf U-Boot in ELF format to transfer u-boot-s.bin and image.ub to flash
u-boot-s.bin relocatable U-Boot in binary format U-Boot on flash
image.ub Linux kernel and root filesystem in binary format Linux on flash
impact.cmd script for impact (not required) transfer download.bit
xmd.ini script for xmd (not required) run u-boot.elf

I am using Platform Cable USB II programmer, usb/uart port is directly connected to the host via minicom.

This is the board connection

Board Connection

Start tftp daemon, and point the working folder to where the above files are.

Start tftp Daemon

Start tftp

Next step is to program FPGA through impact. If you’re using Digilent’s HS1 or onboard JTAG connection, your script should be different.

Program FPGA through impact

Program FPGA

Then download and run U-Boot through xmd. If you’re using Digilent’s HS1 or onboard JTAG connection, your script should be different.

Download and Run U-Boot through xmd

Download and Run U-Boot

If the flash is programmed already, stop the autoboot process from the uart port console, in order to move new U-Boot and Linux to the flash.

Stop Autoboot from uart console

Stop Autoboot

Now it is time to copy Linux kernel and U-Boot to flash. But before doing that, IP addresses for the tftp server (host) and the board (target) need be set. Your IP addresses could be different the ones used below.
Here’s how to do it and copy the Linux kernel (image.ub) to the flash.

IP Addresses setup and copy Linux kernel

IP Setup and Copy Kernel

Then copy the U-Boot.

Copy U-Boot to Flash

Copy U-Boot

Now if everything goes well, you can run Linux by either hitting the reset button or issuing boot command from U-Boot prompt.

Booting Petalinux

Booting

Here’s the booted console, and SPI flash’s partitions.

Booted Console and SPI Flash Partitions

Booted Console and SPI Flash Partitions

You can find listed binary images and scripts here.

Run Linux on Avnet Spartan-6 LX9 MicroBoard

September 6, 2011

AV-LX9 MicroBoard is a new low cost Spartan-6 LX9 device based development kit from Avnet. XC6SLX9
has 1,430 slices, or 5,720 LUTs, and 32 Block RAM. Rich features, such as 64MB DDR, 128Mb SPI Flash, 10/100 Ethernet PHY, USB-UART port, JTAG, LEDs, DIP switches and expansion ports, make the board an affordable and very useful experimental prototyping tool.

Thanks for Avnet’s Frank for the LX9 MicroBoard, I was lucky to be able to try out the board early. My main goal was to get Petalinux running on this this USB-stick form factor board, with httpd server serving web pages and certain peripherals to demonstrate user defined functionalities. After many weekends’ efforts, I was always couple hundreds of LUTs in short to fit designs of MicroBlaze with MMU into LX9 device, even after removing most peripherals, and enabling Legalizer placement algorithm.

Then Petalogix’s John offered me a Linux BSP, used for hobby purpose. This convinced me the goal was possible, and kept me trying my own SOPC designs.

Finally I got it working before the recent Avnet LX9 MicroBoard SpeedWay Design Workshops. The keys were to remove non-essential MicroBlaze features and not use MDM’s JTAG-based UART thus saves a AXI4-Lite connection. I am sure it can go further to use less resources and/or add more peripherals, but still has a stable Linux running on the board.

Here’s how the working design was done in details. I am using PetaLinux SDK 2.1 and ISE 13.2 for 32 bit Linux, starting design flow from Project Navigator.

Create a new project based on Avnet LX9 MicroBoard XBD.

Create New ISE Project

Select Embedded Processor for Source Type with New Source Wizard.

Select Source Type

When BSB starts, choose AXI flow.

AXI Flow

And configure below processor, cache and peripherals.

Processor, Cache and Peripheral Configuration

Once XPS project is created, configure MicroBlaze by double clicking the IP from System Assembly View.

MicroBlaze with MMU Configuration

After select MMU configuration, click Advanced button to fine tune. The following setups can be done by going back and forth to enable then disable certain features. Here’s General configuration.

MicroBlaze General Configuration

Disable all exceptions.

MicroBlaze Exception Configuration

Make sure instruction cache base address is setup properly. This is the location where Linux kernel starts.

MicroBlase Cache Configuration

Here’s MMU setup.

MicroBlaze MMU Configuration

Enable MDM so XMD can be used to debug.

MicroBlase Debug Configuration

No need for Processor Version Registers.

MicroBlase PVR Configuration

Here’s the Interconnection I used.

MicroBlaze Interconnect Configuration

Buses setup is the last MicroBlaze configuration.

MicroBlaze Buses Configuration

Now configure MDM by disabling JTAG UART.

MDM Configuration

Here’s XPS System Assembly View when design is done.

XPS System Assembly View

Return to Project Navigator when XPS is closed. Add constraints by Project > Add Copy of Source.

ISE Add Constraints

Double click Generate Top HDL Source to create HDL instantiation template for the MicroBlaze design.

ISE Generate Top HDL Source

Export hardware design to SDK.

ISE Export Hardware To SDK with Bitstream

If there are errors for placement and routing, try to set environment variable XIL_PAR_ENABLE_LEGALIZER to 1, and rerun PAR.

Here’s my XPS Synthesis Summary (estimated).

XPS Synthesis Summary

Here’s partial ISE Device Utilization Summary.

ISE Device Utilization Summary

Follow PetaLinux SDK Board Bringup Guide to configure software settings of the hardware project and fs-boot.

I am using the following XMD commands to configure FPGA and download Linux image.

This is the PetaLinux login screen.

PetaLinux Login Screen

And PetaLinux Process Status.

PetaLinux Process Status

Another fun experiment is to write code to turn on and off LEDs in certain patterns. 4 bit LED IP’s address is 0x40000000, to turn on all LEDs, you can use:

poke 0x40000000 0x0f

Let me know if you’re interested running my design, I have it here. If you like to try the commercial PetaLinux, please contact Petalogix.